A new air conditioner is one of the biggest purchases most homeowners make, and most people spend their time comparing brands and prices. But the quality of the installation often matters more than the name on the box. A well-installed mid-range system will usually outperform and outlast a premium system that was installed poorly.
These are the installation mistakes we see most often when we’re called to fix “new” systems in Boynton Beach and Palm Beach County, and the questions that help you avoid them.
1. Sizing by rule of thumb
“You had 3 tons, so you get 3 tons” or “one ton per 500 square feet” are shortcuts, not calculations. Homes change: new windows, added insulation, a converted garage, new trees. An oversized system short cycles and leaves the house humid. An undersized one runs constantly and can’t keep up in August.
Ask: “Will you do a load calculation (Manual J) for my home?” Read more in how to size an AC for a Florida home.
2. Ignoring the ductwork
A new system connected to leaky, crushed or undersized ducts won’t deliver its rated efficiency or comfort. Ducts in a Florida attic take a beating from heat over the years.
Ask: “Will you inspect the ducts and tell me if anything needs repair?” Uneven rooms are often a duct issue; see why one room is hotter than the rest.
3. Mismatched indoor and outdoor units
Installing a new condenser on an old air handler might lower today’s price, but the two halves are designed and rated as a matched pair. A mismatch can reduce efficiency and reliability and may affect warranty coverage. With the newer refrigerants used in today’s equipment, matched systems are generally required.
Ask: “Is this a matched system with an AHRI rating?”
4. Reusing a line set without checking it
The copper lines between the indoor and outdoor units must be the right size and in good condition for the new equipment and refrigerant. Some can be reused after proper cleaning and testing; some can’t.
Ask: “Are you replacing or reusing the line set, and how will you check it?” Our article on the R-410A phase-out explains the refrigerant change.
5. Skipping evacuation and proper charging
Before refrigerant is released into a new system, the lines should be pressure-tested for leaks and evacuated with a vacuum pump to remove air and moisture. Moisture left inside can form acids that damage the compressor over time. The refrigerant charge should then be set to the manufacturer’s specification, not guessed.
Ask: “Do you pressure-test and pull a vacuum to a micron reading before charging?”
6. Poor condensate drain work
Florida ACs remove a lot of water. A drain line without proper slope, a trap where the manufacturer requires one, an accessible cleanout or a float switch is how ceilings get stained. This is one of the most common problems we find on recent installs.
Ask: “Will you install a float switch and a cleanout on the drain?” See why AC units leak water.
7. Skipping the permit
In Florida, replacing an AC system generally requires a mechanical permit pulled by a licensed contractor, followed by an inspection. An unpermitted install can create problems with insurance claims and when you sell the house, and it skips an independent check of the work.
Ask: “Is the permit included, and who schedules the inspection?” Also confirm the contractor’s state license; you can look it up on the Florida DBPR website.
8. Weak outdoor unit placement and mounting
In South Florida the outdoor unit needs a solid, level pad, proper clearance for airflow and service, and secure mounting for hurricane-force wind. Units jammed into hedges or against walls run hotter and less efficiently.
Ask: “How will the unit be secured, and is there enough clearance around it?” See protecting your AC during hurricane season.
One more: not registering the warranty
Many manufacturers offer longer parts warranties only if the equipment is registered within a set time after installation. Ask your contractor whether they register it for you, and keep a copy.
Signs your recent installation has a problem
- The house feels humid or clammy even though the system is new
- The system turns on and off every few minutes
- Rooms that were comfortable before are now too warm
- Water in the drain pan or around the air handler
- Power bills haven’t improved, or went up
If any of these sound familiar, a second opinion is worth it. We’re happy to look at systems we didn’t install.
Frequently asked questions
Does installation really matter more than the brand?
Installation quality has a large effect on efficiency, comfort and lifespan. A well-installed system from any major brand will usually serve you better than a poorly installed premium one.
How long should an AC installation take?
A typical replacement takes most of a day. See how long AC installation takes.
How much does a new AC cost in Palm Beach County?
It depends on size, efficiency and ductwork. Our AC installation cost guide gives typical ranges, and our SEER2 guide helps you choose an efficiency level.
Get it installed right the first time
Cold Chillin Air Conditioning sizes every system with a load calculation and explains every step before any work starts. We install across Boynton Beach and Palm Beach County. Licensed (CAC 1823036) and owner-operated. Call (561) 318-1882 or request a free installation estimate. Learn more about our AC installation service.

